What Did You Do To Your HHR Today?
There's good reason the Caravan lasted many years and not the Lumina. It was a sled soon to be boat anchor. That van was a dawg and I LOVE vans!
Was at the lake Sunday with HHR and backed out of driveway today and left a line of sand on the sidewalk. Must have used the air dam for a plow.
Was at the lake Sunday with HHR and backed out of driveway today and left a line of sand on the sidewalk. Must have used the air dam for a plow.
There's good reason the Caravan lasted many years and not the Lumina. It was a sled soon to be boat anchor. That van was a dawg and I LOVE vans!
Was at the lake Sunday with HHR and backed out of driveway today and left a line of sand on the sidewalk. Must have used the air dam for a plow.
Was at the lake Sunday with HHR and backed out of driveway today and left a line of sand on the sidewalk. Must have used the air dam for a plow.
ok this is like my 3rd set of LCA's on my 2006 HHR and not even 95,000 mi yet!!. one being my fault cause i used the stamped steel ones for the cobalt. but at the time i didnt know better.
and at least 3 sets of endlinks!
but on a good note i was done with setup and cleanup in less than an hour and a half!! and no real issue!!
and at least 3 sets of endlinks!
but on a good note i was done with setup and cleanup in less than an hour and a half!! and no real issue!!
If it’s that rear bushing, what brand LCA did you use? Have you considered pressing in a set of Moog problem solver bushings? Do you have Moog greasable ball joints?
Today , just a wash and detailed the exterior, we might go for a short ride to check in on the MIL , all restaurants and fast food joints are closed to indoor dining , Drive thru only, so we’ll be barbecuing steaks for tonight’s supper.
Today , just a wash and detailed the exterior, we might go for a short ride to check in on the MIL , all restaurants and fast food joints are closed to indoor dining , Drive thru only, so we’ll be barbecuing steaks for tonight’s supper.
the first stamped steel were mevrotechs the last 2 have been MOOG's. both the rear bushings and the ball joint rubbers were broken. pic may be too big can someone resize it please?
i am keeping the old set then when have the time will look into rebuilding them. i dont have a press but will see if an autozone has the right tools to press them in first.
Looks like a good project, I use a ball joint press for pressing in the new bushings and an air hammer or even a hacksaw to remove the old bushings , An 1/8 inch drill bit for the pilot hole in each rivet and then 3/8 , then a cold chisel to snap the head off . There are a lot of how too’s on this site and YouTube.
https://www.chevyhhr.net/forums/brak...acement-58018/
We decided to go to the Niagara River at Chippewa and walked about 4 miles total , many cars driving by but only 2 walking folks. Then we went to Starbucks, drive thru only , the store is closed to even the washrooms.
Strange times , very strange.
https://www.chevyhhr.net/forums/brak...acement-58018/
We decided to go to the Niagara River at Chippewa and walked about 4 miles total , many cars driving by but only 2 walking folks. Then we went to Starbucks, drive thru only , the store is closed to even the washrooms.
Strange times , very strange.
Last edited by Oldblue; 03-22-2020 at 04:15 PM.
Daughter said power seat stopped moving down and only up. I disconnected the battery before removing the seat and saw the battery was the original. So I went and got a new battery. Took apart the switch before removing seat and saw she spilled a drink on it. Cleaned it. Installed new battery and seat works again.
told her to stop spilling stuff. She also got a speed photo ticket in the mail today. Told her to toss it in the garbage.
told her to stop spilling stuff. She also got a speed photo ticket in the mail today. Told her to toss it in the garbage.